Simulation
Run a linear static study on the same body you designed, read the numbers and know the limits.
Before you run a study
State the question in numbers first: “does this bracket survive 500 N?” or “is the tip deflection under 1 mm?”. A contour without a criterion is decoration. Decide which body carries the load, which faces are fixed and where the load enters.
The simulation workspace uses the same body you modelled. There is no export, no remesh of a translated copy and no second solver seat.
The study tree
Open the Simulation workspace from the workspace switcher. The feature tree on the left becomes the study tree:
- Bodies — the primary body, plus bonded bodies that touch it.
- Connections — springs and bonded interfaces.
- Fixtures — fixed, roller/slider or hinge, applied to faces.
- External loads — force, pressure, gravity and torque.
- Mesh — element size, curvature refinement and quality.
- Results — stress, displacement, strain, safety factor and the checks.
Material
Pick one of the 12 presets — steel, alloy steel, stainless steel, cast iron, aluminium 6061, brass, copper, magnesium, titanium, ABS, nylon, PLA — or enter your own values:
- Young's modulus and Poisson's ratio for stiffness.
- Yield strength for the safety factor; without it, the factor cannot be computed.
- Density for gravity loads and mass properties.
Say which grade the numbers represent. A study is only as honest as its material card.
Fixtures and loads
- Fixtures: fixed (all directions), roller/slider (one direction free) or hinge. Apply them to the faces that the real support actually holds.
- Force: X / Y / Z components; the value is the total force on the selected faces.
- Pressure: MPa along the inward normal.
- Gravity: from density, in mm/s².
- Torque: N·mm about a vector.
Loads and fixtures can only be applied to faces of the primary body. Bonded bodies transmit load through their contact interface.
Mesh
Start with the default size, or about one thirtieth of the longest side, then refine curved and thin features. Voxel tetrahedra approximate curved surfaces as stair steps, so a curved fillet needs a smaller size than a flat plate.
The mesh panel reports node and element counts and the worst/mean shape quality before solving. A draft-quality mesh is faster for a first look; refine before you sign off.
Solve and read the result
One button meshes if needed and solves the assembled system. The results are painted on the model:
| Result | What to compare it with |
|---|---|
| von Mises stress | Yield strength divided by the required safety factor. |
| Displacement (URES, UX/UY/UZ) | The functional limit — what the part is allowed to move. |
| Equivalent strain | Consistency with the stress contour; a sanity check. |
| Factor of safety | Yield stress ÷ von Mises; below 1 means yielding. |
| Reaction force and moment | Should balance the applied load. |
Click any point to probe stress, displacement, strain and safety factor. Use a section plane to cut through the contour and the mesh.
Convergence and further checks
- Convergence: re-solve at three densities and compare displacement and stress. When both change by less than 5%, the answer has settled.
- Modal: the lowest six natural frequencies, with a normalised mode shape.
- Buckling: the lowest positive load factors and their shapes, from the static stress state.
- Fatigue: a Goodman mean-stress check with endurance limit, ultimate strength and load ratio R, reported at the critical node.
- Report: one click writes an HTML file with the setup, the summary and an inline SVG contour.
Limits
- Linear elastic, small strain. No plasticity, creep, large deformation or hyperelasticity.
- No thermal, thermal stress, CFD or electrostatics.
- No general frictional contact: one primary body plus bonded bodies, with springs for interfaces.
- No explicit dynamics, impact or crash.
- Isotropic materials only; no composite layups.
- Results are not stored with the design. Change the geometry and the study must run again.